Why Upload and Download Options on Powermaster Remote Programmer Not Highlighted

Remote Programmer Software

For PowerMax and PowerMaster

User Guide

Summary of content (87 pages)

• Page 1

  Remote Programmer Software For PowerMax and PowerMaster User Guide

• Folio 2

  Copyrights & Warranty Copyrights & Warranty © Copyright 2014 by Visonic Ltd., 24 Habarzel Street, Tel-Aviv 69710, ISRAEL. All Rights Reserved. No part of this publication may be reproduced or distributed in any form or by any means, electronic or mechanical, for whatever purpose, without the express written permission of Visonic Ltd. Microsoft is a registered trademark of Microsoft Corp.

• PAGE 3

  About This Transmission Well-nigh This Manual This manual provides a detailed clarification of the procedures for using the Remote Programmer with your PowerMax or PowerMaster system. Consult PowerMax and PowerMaster Installation and User Guides for boosted information almost specific programmable parameters. Chapter 1 provides an overview and briefly describes the organization. Chapter 2 lists the requirements for installing the software and describes the software installation procedure.

• PAGE four

  Formatting Conventions Formatting Conventions The following formatting conventions are used throughout the documentation: Note: Additional information relevant to the presently discussed subject area. Alert: Circumspection: Information that is essential for your safety and to avoid damaging the hardware or software. assuming text Indicates operations that yous must perform (east.g., name of a button to exist clicked or option to be selected) or to emphasize a field or concept beingness described.

• Folio 5

  Table of Contents Tabular array of Contents Copyrights & Warranty ........................................................... i About This Manual ................................................................. 2 Formatting Conventions ........................................................ iii Tabular array of Contents ................................................................... iv Chapter 1: Introduction .......................................................... ane Chapter 2: Getting Started ...................

• Folio 6

  Table of Contents Data Indications ................................................................................................. 27 6.1 Site Data .......................................................................................... 27 6.ii User Settings ............................................................................................... 28 6.3 User Codes.................................................................................................. 29 6.4 Panel Defintiions .....

• Page 7

  Table of Contents Chapter 11: Display (Screen Appearance) ............................. lxx 11.1 eleven.two xi.three 11.4 Changing the Colour................................................................................... seventy Column Alignment ................................................................................... 71 User Interface Language ........................................................................... 71 File Naming ...........................................................................

• PAGE 8

  Chapter 1: Introduction Affiliate 1: Introduction The Visonic Remote Programmer is a utility program that enables you to manage the PowerMax/PowerMaster alarm system from a remote station. Information technology runs on IBMPC or uniform workstations and runs on Microsoft® Windows® 7 (32 or 64-fleck), Microsoft® Windows® 8 Desktop (32 or 64-bit) and Windows XP. The Remote Programmer works with the new PowerG wireless applied science and PowerMaster alert systems for intrusion alert systems.

• PAGE 9

  Chapter 1: Introduction Remote Information Transfer enables the operator to work from a remote site where he tin can control several PowerMax/PowerMaster systems at different installation sites. Using the Remote Programmer, he can compare the parameters of the different systems and copy them if necessary. The information is and then transferred to each arrangement through a modem. REMOTE SETUPPOWERMASTER-10 Computer EXTERNA L MODEM TEL.

• Page 10

  Chapter two: Getting Started Chapter 2: Getting Started ii.1 Hardware / Software Requirements In order to run Remote Developer, you lot demand the following resources: · PC (2GHz or higher) · Microsoft® Windows® 7, 8 or XP. · 1GB RAM · At to the lowest degree twenty MB of free deejay space. · For best performance, use a display commuter with a resolution of at least 1024 x 768 pixels. two.

• PAGE xi

  Chapter 2: Getting Started 2.3 Starting Remote Developer 1. On the Windows Desktop, double-click on the Remote Developer icon; the Login screen appears. Figure 2-1: Login Screen 2. In the Operator edit box, type visonic. three. In the Password edit box, type powermax, then click OK. Both entries are instance-sensitive - utilise lowercase letters. The master Remote Programmer screen appears with the well-nigh uploaded recent PowerMax/PowerMaster configuration, including electric current zone enrollment.

• Page 12

  Chapter ii: Getting Started Title bar Card bar Tool bar Table Data Details List of Tables  Status bar Screen Tabs Figure 2-ii: Remote Programmer Main Screen (PowerG Version) Title Bar · · · · The title bar displays the following features: The name of the Remote Developer file that you lot have opened. The windows Minimize button. The windows Maximize button. The windows Shut button. Menu Bar Displays the menus that enable you to access Remote Programmer features.

• PAGE xiii

  Chapter ii: Getting Started Toolbar Remote Programmer provides a toolbar that displays buttons which are shortcuts to the most often used features of the system. Push button Name Function Also accessible through card New Displays the New Sites window. Sites Sites Displays the Sites List window. Sites Relieve Saves the site file displayed on the screen. Sites Search Displays the Sites window (without Site information). View Sites Options Displays the Options dialog box.

• Page 14

  Chapter 2: Getting Started Button Proper noun Function Likewise accessible through menu Help Displays the Remote Programmer Assist files. Assistance Device Configuration Performs device configuration. - Stop Terminates device configuration process. - P. Test Starts a walk-test on the enrolled zones or devices referred to in the displayed table. The test starts later y'all initiate it on the device Status Bar The Condition Bar appears at the lesser of the Remote Programmer screen.

• Folio 15

  Chapter 2: Getting Started ii.5 Navigating Around Remote Programmer Yous can move around the Remote Programmer screen and comport out functions in a multifariousness of ways: Mouse · · · · Use the mouse to signal to a position on the screen, and then click the left mouse push. This enables you to do the post-obit: Click a button. Select a tabular array tab in the primary screen. Place the cursor within a table edit box. Brandish a drib-down list.

• Page 16

  Chapter 3: Menus Affiliate 3: Menus The Remote Programmer primary screen displays six menus, which enable you to access the different features of the awarding. 3.one Sites Menu The Sites carte du jour provides yous with the tools to manage new and existing Sites. Menu Item Function List of Sites Displays the Sites window (with Site information). New Site Displays a new Remote Programmer Site File that contains default values. Search Displays the Sites window (without Site information).

• Folio 17

  Chapter iii: Menus 3.3 View Menu The View menu contains items that enable yous to control the appearance of your Remote Programmer screen. Carte Item Function Toolbar Displays or hides the Tool bar Status Bar Displays or hides the Status bar. Adjacent Tabular array Displays the side by side table of the Listing of Tables. Previous Tabular array Displays the previous tabular array of the Listing of Tables. Messages Window Displays the incoming and outgoing messages. Options Displays the Options dialog box. 3.

• Page 18

  Chapter 3: Menus Customize Zone/Sensor Names∗∗ Enables modification of the five custom names. Upload Customized Zone/Sensor Names∗∗ Retrieves the updated custom names from the PowerMax/PowerMaster. Port Auto Detection… Automatically begins a search for the control panel that is continued by Serial Communication fashion. Settings Opens the Options dialog box, on the Communications tab. 3.5 Advanced Card The Advanced carte includes items that enable you lot to receive additional command panel information.

• PAGE 19

  Chapter 3: Menus 3.6 Help Menu The Help carte enables yous to receive information and guidance in managing Remote Programmer. 12 Menu Item Function Help Topics On-line Help to increment your knowledge about Remote Programmer, and assist you lot use it to its maximum potential. Nigh Remote Programmer Provides Remote Programmer copyright and version information. Click on the Remote Programmer logo to display our Abode Folio. Catalog and Series Provides control panel manufacture data.

• Folio 20

  Chapter 4: Sites Chapter 4: Sites 4.1 Introduction to Sites The Remote Programmer enables you to manage security organisation installation sites in a variety of means. These features are attainable either from the menus or from the Site List window. The Site List window is displayed either when the program is first initiated, or by clicking the Sites button in the tool bar or by selecting List of Sites in the Sites card. Note: The Site List window opens with information contained in the folder of the Sites Location.

• Page 21

  Chapter 4: Sites Each cavalcade of the site list table can exist sorted in either descending or ascending order by clicking on the column title. You tin can drag the vertical lines that separate the columns to enlarge or reduce the size of the columns. The screen displays buttons, which enable you lot to brainstorm working with Remote Programmer: Button Part Open Opens an existing Site New Opens a new Site Delete Deletes a Site Exit Closes the Remote Programmer application.

• PAGE 22

  Chapter 4: Sites 4.2 Creating a New Site Y'all tin create a new, empty site file or you tin can copy an existing file, relieve information technology under a new name, and make the relevant changes to tailor it to a similar setup as the original. You can create a new site either via the Site List window or straight in the New Site window. Click New in the Site List window, or In the Sites carte, click New Site.… The New Site dialog box appears.

• PAGE 23

  Chapter 4: Sites Working Online To work via a serial port ane. In the New Site window click Options…. The Options window appears. Effigy 4-4: Options - Serial Port Communications Mode two. Ensure that Serial port is selected in the Communication way field and that the serial port details are correct (refer to chapter vii: Connecting to the Command Panel for farther details). iii. Click OK.

• PAGE 24

  Affiliate 4: Sites Figure 4-4: New Site Window - Work Online via a Serial Port four. Enter the download code located in the control panel (for further details, come across relevant PowerMax or PowerMaster User Guide). The Login push button will become enabled. five. Check the Car Detection checkbox if you desire the program to automatically scan the computer ports to detect PowerMax/PowerMaster presence.

• Page 25

  Chapter 4: Sites To piece of work via a phone modem 1. In the New Site window click Options…. The Options Communications dialog box will appear. Figure four-5: Options - Telephone Modem Communications Mode 2. Select Telephone modem in the Communications fashion field. 3. Click OK. The New Site window will appear displaying the Work Online tab with the Phone Number field enabled and the Motorcar detection checkbox disabled. 18 DE5450S Remote Developer Guide Rev.

• Folio 26

  Affiliate 4: Sites Effigy iv-6: New Site Window - Telephone Modem Mode 4. Enter the Phone Number and the Download Code located in the control console (for further details, come across PowerMax or PowerMaster User Guide). The Login button will become enabled. v. Click Login. The Modem Dial Up... window will appear and attempt connecting. Figure iv-7: Modem Punch Upward... DE5450S Remote Developer Guide Rev.

• PAGE 27

  Chapter four: Sites Working Offline Work Offline only if yous know the panel model yous desire to connect to. ane. Select the Piece of work Offline tab. The post-obit screen will exist displayed: Figure four-eight: New Site Window - Work Offline 2. Select the relevant panel model. Note: The Piece of work Offline dialog box beginning lists all existing PowerMax/PowerMaster models. Select each model yous exercise not require and click the Remove button to delete the model from the list. To reset the list, click the Load button. three. Click OK.

• Folio 28

  Chapter 4: Sites 4.4 Saving a Site File with a New Name This enables you to relieve the site file with a new name and in a different directory. 1. From the Sites carte du jour, select Save Equally; Remote Programmer displays the Salvage Equally screen. 2. Enter a suitable name for the new site and locate the directory where you desire to salve the file. Note: In the Option - Brandish tab (meet Chapter xi), if the File Naming section is checked, the file proper name must include the business relationship number.

• PAGE 29

  Chapter 4: Sites 4.seven Deleting a Site When a Site is no longer active, and it is no longer necessary to store it in Remote Developer, y'all can delete it. one. In the Sites List, select the site to delete, so click Delete, a alert box appears reminding you that any account that you delete is non retrievable. 2. Click Yes to delete the business relationship, or No to return to the Sites Listing. If yous click Yep, the Remote Developer principal window appears and displays the concluding site that was opened. 4.

• Folio 30

  Chapter v: Users Chapter v: Users From the Sites menu, select Users; the Remote Programmer displays a menu that enables you to manage the Remote Developer users. Carte Detail Enables you lot to: Add new user Add a new user proper noun and countersign. Delete user Delete a user name and password. Change password Change an existing user'due south password. Login equally different user Login as a dissimilar user without exiting Remote Programmer. 5.1 Adding New Users 1.

• Folio 31

  Affiliate five: Users 5.two Deleting a User 1. From the Sites menu, select Users, then Delete user; the Delete user dialog box will appear. Effigy 5-2: Deleting User Proper name Dialog Box 2. In the User Name edit box, blazon the user'due south name. iii. In the Password edit box, type the user's password. 4. Click Delete; a message box appears confirming the deletion of the user from the organisation. 5.iii Login as a Different User 24 1.

• PAGE 32

  Affiliate six: Information Details Tables Chapter 6: Data Details Tables The data details tables display the parameters that can be uploaded from or downloaded to the PowerMax/PowerMaster control console. When get-go creating a site file, the values displayed are default values, which can be altered to suit the specific arrangement. Use the arrow keys to navigate between the cells and focus on the unlike parameters, then click the left mouse push or press ENTER to edit the prison cell and change the values.

• PAGE 33

  Chapter six: Data Details Tables 26 PowerMax PowerMaster Keyfob Enrollment Repeater Enrollment -- 1W Keypad Enrollment -- 2W Keypad Enrollment Pendant Enrollment -- Keyfob Definitions -- Keypad Definitions -- Siren Definitions -- Prox Tag Definitions Zone Definitions - Motion -- Zone Definitions - Contact -- Zone Definitions - Fume -- Zone Definitions - Camera -- Zone Definitions - Flood -- Zone Definitions - Gas -- Zone Def

• PAGE 34

  Chapter six: Data Details Tables Data Indications This table is applicable to the PowerG models. The various data tables display data that has been uploaded to the remote direction from the PowerMaster system's various devices, such as the command panel, detectors, keyfobs, and sirens. When configuration or status data is modified and/or downloaded, the table entries are color coded to point the status of the displayed information: • Light-green – Data remains unchanged.

• PAGE 35

  Chapter 6: Data Details Tables Note: If there is no entry for the secondary telephone number, the Remote Programmer will dial the primary phone simply. Note: If the dialed telephone number is engaged or there is no reply, the Remote Programmer will toggle betwixt the primary phone number and the secondary telephone number. Time Zone: Select from the list the relevant time zone. Download Code: A 4-digit password, including messages A-F, used to enable downloading data to the command panel.

• PAGE 36

  Chapter 6: Data Details Tables vi.3 User Codes This tabular array defines the PowerMax/PowerMaster users and lists their codes. Merely users, whose numbers and codes are listed in this screen, can activate the control panel. PowerMax and PowerMaster-10 can store up to 8 user numbers and codes. PowerMaster-xxx can store upwardly to 48 user numbers and codes. All User codes must exist different from the Duress code and Installation code. User Number one is known equally the Master User.

• Page 37

  Affiliate 6: Data Details Tables vi.vii Internal Siren/Strobe This defines the operation of the INT output in the control panel. Internal Siren - enables you to activate the output for a certain amount of (Bell) time. Strobe - activates the output until the system is disarmed. six.8 Ten-x General Features∗ This screen enables you to fix the general features for the X-ten units. The House Code must be a letter between A and P that distinguishes this particular PowerMax X-10 unit of measurement from others. 6.

• Folio 38

  Chapter six: Data Details Tables 6.10 External Voice Box The PowerMax Speech Box is a device that enables home occupants to hear notifications and converse with the central station from areas of the habitation that the panel's congenital-in speakers and microphones do non reach. This table indicates whether or not a vox box is installed and is the simply voice device enabled for communication, or if it is mixed within the protected area. 6.11 Zone Enrollment This table is applicable to the PowerG models.

• PAGE 39

  Affiliate 6: Information Details Tables To Complete the Enrolling Procedure half dozen. Stand near the PowerMaster console. Press and hold the enroll button of the device until the orange LED turns on, and then release the push. Ensure that the LED stays on for two seconds and and then flashes for x seconds. seven. Click the UL Table icon viii. To view the zone's RSSI, click OK in the dialog box that opens. 9. Make certain that "Activated" at present appears in the Enrolled column. . To Perform a Periodic Exam i.

• PAGE 40

  Chapter vi: Data Details Tables To Pre-enroll a Siren on the Remote Programmer one. Login to the Remoter Programmer. 2. In the Siren Enrollment tabular array, click an "Unregistered" Activeness button 3. In the dialog box that opens, brand sure the Add Device radio button is selected and enter the siren ID. . Figure vi-2: Pre-Enroll Dialog Box 4. Click the Send to Panel button and so click Close. 5. Click the UL Table icon . To Complete the Enrolling Procedure half-dozen. Stand about the PowerMaster panel.

• PAGE 41

  Affiliate 6: Information Details Tables To Perform a Periodic Test i. Click the Periodic Examination icon on the toolbar. 2. Press the cocky-test push on the siren one time and release it. 3. Make certain that "Tested" at present appears in the Walk Test column. To Delete a Siren 1. In the Siren Enrollment table, click the Action button deleted. 2. From the dialog box, select the Delete Device radio push button. 3. Click the Send to Panel push button. 4. A new dialog box opens asking Are you sure?; click Yes. 5. Click Shut.

• PAGE 42

  Chapter 6: Information Details Tables 1. Enroll the keyfob transmitter to the command panel as detailed in the PowerMax Installer Guide. Note: Remember the keyfob number to which you enrolled the keyfob. 2. Connect and log in via series connection to the panel as detailed in affiliate 7: "Connecting to the Control Panel". 3. Upload the keyfob data from the panel. four. In the Keyfob Enrollment table, enter the keyfob ID, the sync. counter and the sync.

• PAGE 43

  Chapter 6: Data Details Tables To Pre-enroll a Keyfob on the Remote Programmer 1. Login to the Remoter Developer. two. In the Keyfob Enrollment table, click an "Unregistered" Activeness button 3. In the dialog box that opens, brand sure the Add Device radio push is selected and enter the keyfob ID. . Effigy vi-iii: Pre-Enroll Dialog Box 4. Click the Send to Console button and then click Close. 5. Click the UL Tabular array icon . To Complete the Enrolling Procedure 36 half dozen. Stand about the PowerMaster panel.

• PAGE 44

  Chapter 6: Data Details Tables To Perform a Periodic Test i. Click the Periodic Test icon on the toolbar. 2. Press the Arm AWAY button. iii. Make sure that "Tested" now appears in the Walk Test column. To Delete a Keyfob 1. In the Keyfob Enrollment table, click the Action push button be deleted. 2. From the dialog box, select the Delete Device radio button. three. Click the Send to Panel button. iv. A new dialog box opens asking Are y'all sure?; click Yes. v. Click Close.

• Page 45

  Affiliate 6: Information Details Tables Figure six-four: Pre-Enroll Dialog Box 4. Click the Transport to Panel button and then click Close. five. Click the UL Tabular array icon . To Complete the Enrolling Process 6. Stand near the PowerMaster panel. Press and hold the enroll button of the repeater until the orangish LED turns on, and then release the push button. Ensure that the LED stays on for ii seconds and then flashes for 10 seconds. 7. Click the UL Table icon . 8.

• Page 46

  Chapter 6: Data Details Tables To Delete a Repeater 1. In the Repeater Enrollment table, click the Action push button repeater to be deleted. 2. From the dialog box, select the Delete Device radio button. iii. Click the Send to Panel push button. 4. A new dialog box opens asking Are you lot sure?; click Yes. 5. Click Close. of the The repeater is at present deleted from the system. half-dozen.16 Keypad Enrollment An MCM-140 (i-way) keypad is a multi-button wireless keypad unit.

• Page 47

  Chapter 6: Information Details Tables The keypad that is to be enrolled and sent to the customer. 1. Enroll the keypad to the control console as detailed in the PowerMax Programming Guide. 2. Connect and login via serial connectedness to the control console as detailed in chapter 7: "Connecting to the Control Console". 3. Upload the keypad data from the panel. four. In the Keypad Enrollment tabular array, enter the keypad ID, the sync. counter and the sync.

• PAGE 48

  Chapter half-dozen: Data Details Tables To Delete a Keypad In the ID column, change the ID to 00000000, and so download to the control panel every bit detailed in chapter 7: Connecting to the Control Panel. six.17 2W Keypad Enrollment A 2W (two-way) keypad, such as KP-140 PG2, is a multi-button wireless keypad unit. The Remote Programmer displays all enrolled 2-way keypads. To Pre-enroll a 2W Keypad on the Remote Programmer one. Login to the Remoter Programmer. 2.

• PAGE 49

  Chapter 6: Data Details Tables Figure vi-5: Pre-Enroll Dialog Box 4. Click the Send to Panel push button and then click Close. 5. Click the UL Table icon . To Complete the Enrolling Procedure 42 vi. Stand near the PowerMaster panel. Press and hold the AUX button until the orangish LED turns on, and and then release the button. Ensure that the LED stays on for 2 seconds and and so flashes for x seconds. 7. Click the UL Table icon eight. To view the keypad's RSSI, click OK in the dialog box that opens. 9.

• PAGE 50

  Affiliate half-dozen: Data Details Tables To Perform a Periodic Examination i. Click the Periodic Test icon on the toolbar. 2. Press whatever cardinal on the keypad. 3. Brand sure that "Tested" at present appears in the Walk Test cavalcade. To Delete a Keypad 1. In the Keypad Enrollment table, click the Action button keypad to be deleted. 2. From the dialog box, select the Delete Device radio button. 3. Click the Transport to Panel push button. 4. A new dialog box opens asking Are yous sure?; click Yeah. 5. Click Close.

• PAGE 51

  Chapter 6: Information Details Tables Figure half dozen-vi: Pre-Enroll Dialog Box four. Click the Send to Panel button then click Close. 5. Click the UL Tabular array icon . To Complete the Enrolling Procedure half dozen. Stand up near the PowerMaster console. Printing and hold the push (for PB-101) or the left push button (for PB-102) until the orangish LED turns on, and then release the push. Ensure that the LED stays on for 2 seconds and and so flashes for 10 seconds. 7. Click the UL Tabular array icon . 8.

• Page 52

  Chapter half-dozen: Data Details Tables To Delete a Pendant ane. In the Pendant Enrollment table, click the Action push button pendant to be deleted. 2. From the dialog box, select the Delete Device radio push button. 3. Click the Send to Panel button. 4. A new dialog box opens asking Are you sure?; click Yes. 5. Click Close. of the The pendant is now deleted from the organisation. 6.

• Folio 53

  Chapter six: Data Details Tables Figure six-7: Status Diagnostics Note: The Channel Lst. Msg. column displays the terminal channel on which information was transmitted betwixt the zone'due south installed device and the control console. When the transmissions between the control panel and devices change channels, the channel indication is displayed in various colors, such as the purple and yellowish indications in the above figure. 46 Condition Description of Yes state Bypass Bypassing of zone is enabled.

• Page 54

  Affiliate 6: Information Details Tables Condition Clarification of Yeah country UNSET – Organization is disarmed. PERIODIC TEST – Periodic test (walk test) in procedure. DIAGNOSTIC TEST – Diagnostic test in procedure. one-Way ONLY Communication between device and control panel occurring in one direction only. PRE-ENROLLED Enrollment of the device is not consummate – device needs to be associated with the control console. NOT UPDATED Device configuration has not been updated notwithstanding from the command panel.

• PAGE 55

  Chapter half-dozen: Data Details Tables vi.21 Panel Status/Trouble This table is applicable to the PowerG models. The Panel Status/Trouble screen displays diagnostic information that is uploaded from the Control Panel. A Yes indication alerts that a condition exists that needs checking. A No indication means that the condition is normal. 48 Condition Description Condition 1/ STATUS ii Armed/Disarmed, Ready/Not Ready Depression Battery Control Panel'southward battery needs replacement or is non connected.

• Page 56

  Chapter vi: Data Details Tables half-dozen.22 Consequence/History Log∗ ∗∗ The Result Log displays the dissimilar events that the control panel has detected, together with their details. The Remote Developer stores up to 100 events. This table includes: event number; relevant zone or user number/lawmaking; relevant zone name; blazon of event; date and fourth dimension. The History Log displays upwardly to 1000 different events that the control panel has detected and stored in a dissimilar folder. half dozen.

• Folio 57

  Chapter 7: Connecting to the Control Panel Chapter 7: Connecting to the Control Panel Connecting to the PowerMax/PowerMaster control console enables the Remote Developer to transfer information to and from the command panel. The control panel can exist connected by remote connection (via telephone modem), used when the operator specifies the parameters off-site, or by local connection (via direct cablevision), used when the operator specifies the parameters on-site.

• Page 58

  Chapter 7: Connecting to the Command Console 7.1.1 Local Connection (Serial Port) Local connection is used when the Remote Programmer is within direct cable connexion distance from the PowerMax/PowerMaster control panel. When using Local Connection, a modem is not needed. 1. From the Communications mode drop-down list, select Serial Port. The serial port parameters are displayed equally follows: • The Comm port field becomes enabled.

• Folio 59

  Affiliate seven: Connecting to the Command Panel seven.i.2 Remote Connection (Telephone Modem) This is applicative when the Remote Programmer is off-site and the PowerMax/PowerMaster control panel on-site is connected to Remote Developer by a telephone modem. 1. From the Communications manner drib-down list, select i of the following advice options: Modem Type Clarification PSTN straight Dials to the control panel by the PSTN line at a baud charge per unit of 300.

• PAGE threescore

  Affiliate vii: Connecting to the Control Panel i) The user needs to obtain a digital number for the GSM unit. The Remote Programmer is then able to connect to the GSM unit via digital communication (at a baud charge per unit speed of 9600). ii) DTMF callback connexion uses a special GSM modem (Sony Ericsson Modem GM29) which uses a digital number. The Remote Programmer dials the GSM unit via analog communication, merely, instead of sending data it uses DTMF tones.

• PAGE 61

  Chapter 7: Connecting to the Control Panel 3. Click Settings to display the Modem Settings dialog box, and define the dialing and modem parameters. Figure 7-v: Modem Settings 4. Select Tone or Pulse as appropriate for the dialing manner. v. To connect to the control panel'south modem, the local software initiates the dialing process. This procedure includes a number of steps: Step 1: Dialing. Step two: Waiting 2-4 rings (The dialing procedure ends if connexion is made). Step 3: Hanging upward.

• Folio 62

  Affiliate 7: Connecting to the Command Panel The time entered into the Expect for Connexion field should exist no less than the time entered in the Wait for 2-4 rings during field. The Wait for Connection field defines the time (in seconds) it takes to dial to the control panel, for the command panel to answer, and for the command panel modem and the PC to establish connection. Tip: If yous are not sure of the fourth dimension to enter in the Await for 2-4 rings during and Expect for Connectedness fields, enter a high number (i.due east.

• PAGE 63

  Affiliate 7: Connecting to the Command Panel 7.one.3 Callback In the Phone number field the user enters the Remote Programmer return telephone number (the telephone number that connects to the modem). In the Wait earlier sending field, the user enters the amount of time (in seconds) the Remote Programmer waits before identifying the call as failed. Effigy 7-7: Callback Telephone Number String 7.

• Folio 64

  Chapter 7: Connecting to the Control Panel Connecting by Local Connection (Serial Port) After clicking Login, the communication icons in the status bar will go green, and the Download and Upload icons in the toolbar get enabled and you accept successfully logged in. Connecting by Remote Connection (Phone Modem/GSM/Callback) When connecting by phone modem, subsequently clicking Login, the Modem punch up dialog box appears. Figure vii-viii: Modem Dial Up...

• Page 65

  Chapter 7: Connecting to the Control Panel 7.iii Online Operations While continued to the PowerMax/PowerMaster command panel, you can perform the following operations: • Check if the detectors in the various zones are enrolled and communicating with the control panel. • Transfer information between the Remote Programmer and the control panel by uploading or downloading either all site parameters or a specific tabular array. • Update the system appointment and time.

• PAGE 66

  Chapter 7: Connecting to the Control Panel Figure 7-nine: Uploading/Downloading Progress Bar Screen At whatever point during the transfer, click Abolish to halt the procedure. When the transfer is complete, a bulletin box appears to confirm successful completion. Note: In PowerMax+, this process uploads all parameters except for the Effect Log. To upload the Event Log follow the To Upload a Specific Table procedure.

• Page 67

  Chapter seven: Connecting to the Control Panel three. In the Electric current time edit box, blazon the time. Use either the 12 or 24 hour clock format according to the current time settings. iv. Click Send; Remote Programmer saves the modified engagement and time, and updates the Control Panel. To Update Customized Zone/Sensor Names 1. From the Communications menu, select Customize Zone/Sensor Names; the Customize Zone/Sensor Names dialog box appears. Effigy 7-11: Customize Zone/Sensor Names Window 2.

• PAGE 68

  Chapter eight: Data Chapter viii: Information The data tab is used to define specific upload/download settings to facilitate data transfer. 8.1 Defining Information Settings The Data dialog box enables you to customize specific data settings in the upload/download procedure. From the View menu, select Options, and then click on the Information tab; the Data dialog box appears. Applies only to PowerMax+ Figure 8-1: Options – Data Tab (PowerG Version) Annotation: The contents of the Data dialog box may vary for each control panel version.

• Page 69

  Chapter viii: Information 1. Check the Send updated data immediately field, to automatically update changed settings from the Remote Programmer to the command panel. Note: If the higher up field is non checked, the command console volition just be updated when performing download table or total download. ii. In the Delay afterwards acknowledge during download field, enter a fourth dimension value (in milliseconds) for a delay in sending commands. This field should be used when bug in communication is experienced. 3.

• Folio 70

  Affiliate 9: Two Download Codes Chapter 9: Two Download Codes This document explains the use of ii download login codes - located in the control panel (for further details, run across PowerMax/PowerMaster User Guide) - used for the two types of access codes, as follows: • Master Installer – used to gain access to all the data in the control panel (commonly used by the central station). • Installer – used to proceeds access to all the data in the control panel except for central station data. 9.

• Folio 71

  Chapter 9: Two Download Codes Installer The installer enters the Installer download code and is assigned an Installer privilege. Special cases A. Master and Installer as the same Download Code: The PowerMax/PowerMaster control panel e'er confirms whether the download code is Principal or Installer. In the event that the Master and Installer lawmaking are identical, the Remote Programmer volition assign an Installer privilege. To regain Master privilege 1. Log into the Remote Programmer. 2.

• Page 72

  Chapter 9: Two Download Codes Figure 9-1: Site Information Download Code Site Data Main Download Code For Remote login Installer Download Code For Remote login Chief Installer Code Panel Installer Code Panel DE5450S Remote Developer Guide Rev.

• Folio 73

  Chapter x: Reports Chapter 10: Reports After y'all have created a site, you can generate a printable report of the site data. To generate a report, first define the information to include in the report, preview the report then print information technology. ten.i Defining and Generating a Written report Each Remote Developer account comprises of 12 tables. You can generate a report including information well-nigh some or all of these details. After you specify the required details, Remote Programmer volition generate the report.

• Page 74

  Chapter ten: Reports Marking the check boxes to specify the information to include in the Report. iii. Click Utilize; the tables to include in the study are selected, and the Reports dialog box remains on the screen for further perusal and selection. 4. Click OK; Remote Developer generates the study according to your specifications. 10.ii Viewing a Written report Remote Programmer enables you to view reports before you print them.

• Folio 75

  Chapter x: Reports 10.3 Printing a Written report You can modify the impress setup for a study. This enables you to determine the following: · The printer to print the report. · The paper size on which to impress. · The source from which the printer should accept paper. · The orientation of the paper. To Determine the Print Setup i. From the Sites menu, select Print Setup; the Print Setup dialog box appears. 2. Specify the printer to where the study will be printed. 3.

• PAGE 76

  Affiliate 10: Reports This screen enables you to do the following: • • • Select the printer to print the report. Determine the print range. Determine the number of copies of the report, and whether or not they should be collated. 2. Make the advisable changes, then click OK; Remote Programmer prints the report. DE5450S Remote Programmer Guide Rev.

• PAGE 77

  Chapter 11: Display (Screen Appearance) Affiliate 11: Brandish (Screen Appearance) Whatsoever changes to the appearance of the Site screens are made in the Display tab of the Options dialog box. Figure 11-1: Options - Brandish Tab 11.1 Changing the Color The colors of the Table Details are divers according to the following settings: 70 • Table zebra color: Defines the colour of every other line in each table. This makes it easier for the user to follow the horizontal lines in the table.

• Page 78

  Chapter eleven: Display (Screen Appearance) To Change the Tables Color 1. From the View menu, select Options; the Options dialog box appears. Past default, the display tab is active. 2. Click on the cake of Tables zebra colour; the color palette appears. 3. Select a color, and so click OK. 4. Restart Remote Programmer. 11.

• PAGE 79

  Affiliate 11: Display (Screen Appearance) xi.4 File Naming This section provides you with the option for making compulsory the inclusion of the account number in the file name. To Enable the Account Number in the File Name Feature 72 1. In the File Naming section; check the File name must include the Account Number check box. two. Click OK. DE5450S Remote Programmer Guide Rev.

• PAGE lxxx

  Chapter 12: Troubleshooting Chapter 12: Troubleshooting Trouble A. The Remote Programmer doesn't identify the modem DIAGNOSIS A1. Your modem might be OFF or loosely connected. A2. You lot may have a COM\IRQ conflict. B. Failure to comB1. You lot may accept a municate with the disharmonize with the control panel via definitions in the the modem. advice fashion window. B2. Your modem is set to work at a high baud rate. B3. The modem type is different from the type displayed in the OPTIONS bill of fare / Communications tab.

• PAGE 81

  Affiliate 12: Troubleshooting PROBLEM DIAGNOSIS POSSIBLE SOLUTION B. Failure to comB5. Modem is not B5. Make sure that the modem is municate with the properly installed recognized by Windows. control panel via in operating If not, click Beginning → Setting → Control the modem. system Panel. Double click the Modems icon (cont.) (Windows). and follow the instructions on the displayed Install New Modem window. C. PC fails to communicate with the command panel via the Series Port. D.

• Page 82

  Chapter 12: Troubleshooting PROBLEM DIAGNOSIS D2. Control panel doesn't permit you to login. This is due to: a) The organisation being in Away land and the control panel is set to permit upload but at Disarm country. POSSIBLE SOLUTION D2. a) Disarm command panel, and then change upload setting to Any Time. b) Look until the Get out/Entry state terminates and the command console enters a valid state (Disarm/Arm/Dwelling). So, login again. b) The organization being in Get out/Entry country. E. The programme E1. Yous may have E1.

• PAGE 83

  Appendix A: Language Settings Appendix A: Language Settings When using the Remote Programmer Software in Windows XP with a foreign language interface, some characters may not appear correctly in the chosen language. This may require irresolute the language settings. Windows XP one. From Start>Settings>Control Panel double-click Regional and Language Options. The Regional and Language Options dialog box appears. Figure A-1: Regional and Language Options Window 76 2. Click on the Avant-garde tab. 3.

• Folio 84

  Index Index 1 H 1W Keypad Enrollment Screen, 39 Hardware/Software requirements, 3 2 2W Keypad Enrollment Screen, 35, 41, 43 Assist Menu, 12 A Installation general, three software, 3 Auto Detection, 51 C Communication Settings, 50 Communications Definitions Screen, 29 I Internal Siren/Strobe Screen, 30 1000 Keyfob Enrollment Screen, 34 Communications Menu, ten 50 Connecting, 52 via serial port, 51, 57 Language, changing, 71, 72 Creating site, 15 Local Connection, 51, 57 D Disconnecting from PowerMax

• PAGE 85

  Carte Bar, 5 Siren Enrollment Screen, 32 Modems declining to communicate with, 73, 74 bug identifying, 73 settings, 54 Site Information Screen, 27 North Sites creating new, 15 displaying list of, 13 window, 13 Navigating PowerMax Remote Developer arrow keys, 8 mouse, 8 Software exiting, 8 Initiating, 4 installing, 3 requirements, three O Status Bar, 7 Online Operations, 58 System Time & Date, changing, 59 P T Console Definitions Screen, 29 Tabular array Information, v Panel Status/Problem Screen, 48 Table Item

• PAGE 86

  Index codes screen, 29 delete, 23 login equally different, 23 settings screen, 28 zone status/trouble screen, 45 Telephone Modem, connecting via, 52, 57 Title Bar, v Tool Bar, half dozen Troubleshooting, 73 login failure, 74 modem communication, 73, 74 modem identification, 73 serial port advice failure, 74 U Upload all site parameters, 58 table, 59 User add, 23 change password, 23 DE5450S Remote Programmer Guide Rev.

• PAGE 87

   2014 Tyco Security Products. Remote Programmer Software User Guide, DE5450S (Rev.

fleenoriltor1986.blogspot.com

Source: https://www.manualshelf.com/manual/visonic/powermax-remote-programmer-software/user-guide-english.html

Share this post